How Do I Control My Gree AC Remote? Full Guide

To control your Gree air conditioner with the remote, point it at the unit and press the On/Off button to start it, use Mode to pick cool, heat, dry, or fan, set the temperature with the up and down arrows, and adjust airflow with the Fan button. Fresh batteries help the signal reach the unit reliably. Those four controls — power, mode, temperature, and fan — cover the everyday use of any Gree remote. Beyond the basics, Gree remotes include handy extras like the “I Feel” function, a timer, and swing control. Below we walk through changing the temperature, what “I Feel” actually does, the common remote symbols, and how to troubleshoot a remote that isn’t responding.

How do I change the temperature in Gree AC?

Changing the temperature on a Gree AC is done right from the remote and takes a couple of button presses.

Make sure the unit is on and set to a mode that controls temperature (Cool or Heat). Then press the up or down arrow buttons to raise or lower the set temperature until you reach the level you want.

Press the up or down arrow on the remote until your desired temperature shows on the display. The set temperature appears on the remote’s screen, and the unit will work toward it.

For best efficiency, make modest adjustments rather than jumping to an extreme setting — a small change reaches the target faster and with less strain on the unit.

What is “I feel function” in Gree AC?

The “I Feel” function in a Gree AC uses a temperature sensor built into the remote. When you turn it on, the air conditioner adjusts based on the temperature the remote detects, instead of the sensor in the indoor unit.

The practical benefit: place the remote next to you, and the AC works to make your spot comfortable rather than the area around the unit. Press the I Feel button while the unit is on to toggle it; an I Feel icon appears on the display when it’s active and disappears when it’s off.

For it to work properly, keep the remote within signal range of the unit and out of direct sun or drafts, so the sensor reads the real room temperature where you are.

What are the symbols in AC remote?

Gree and most AC remotes share a common set of symbols. The core ones are power (on/off), mode, fan speed, and temperature, and each symbol has its own job.

The power button turns the unit on or off. The mode button cycles through the operating modes — typically a snowflake for cool, a sun for heat, a water drop for dry/dehumidify, and a fan for fan-only. The fan button steps through fan speeds (low, medium, high, and often auto).

The arrow buttons set the temperature. You’ll also commonly see a swing symbol (for the louver direction), a timer, sleep mode, and the I Feel icon. If a symbol is unfamiliar, your model’s manual lists the exact meaning for that remote.

How To Use Gree Ac Remote Control Function

Gree air conditioner remote control app

Many Gree air conditioners can also be controlled from a phone using Gree’s app (such as Gree+), which lets you operate a Wi-Fi-capable unit without the physical remote.

The app is available for Android and iOS. After installing it, you typically connect the AC to your home Wi-Fi and pair it in the app following the on-screen steps. (Check your model’s manual for the exact pairing process and whether your unit needs a Wi-Fi module.)

Once paired, you can use the app like a remote — turning the unit on and off, setting the temperature, and changing modes from your phone.

The app also supports scheduling, so the AC can turn on and off automatically, and it can manage multiple compatible Gree units from one place. It’s a convenient option if you’d rather not rely on the handheld remote.

How to use gree ac remote for heater

If your Gree unit is a heat pump (reverse-cycle), the remote controls heating through the Mode button.

Use these steps to switch to heating:

• Press the “Mode” button to cycle through the settings until you reach Heat (the sun symbol).
• Use the up or down arrow buttons to set the temperature you want.
• Use the On/Off button to turn the unit on or off.
• Press the “Fan” button to set the fan speed.
• To set a timer, press the “Timer” button, use the arrows to set the time, then confirm per your remote.

Note that not every Gree model heats — cooling-only units have no Heat mode. Check your model’s spec or manual to confirm it’s a heat pump.

Gree ac remote not working

If your Gree remote isn’t responding, work through the simple checks first. Replace the batteries — weak batteries are the most common cause, and the signal fades before the remote looks fully dead.

Make sure you’re pointing the remote at the unit’s receiver with nothing blocking the line of sight, and that you’re within range. Bright sunlight on the receiver can also interfere.

If new batteries and a clear line of sight don’t help, try resetting the remote (see the next section). Still nothing? Contact Gree customer service or consider a replacement remote — confirm it’s compatible with your model.

How to reset gree ac remote

Resetting can clear a glitched remote and the unit’s settings.

Here’s a common approach:

1. Unplug the air conditioner from the power outlet.
2. Remove the batteries from the remote control.
3. Wait about a minute, then look for a recessed reset button on the remote (often pressed with a pin) and press it if present.
4. Replace the batteries in the remote control.

Plug the air conditioner back in. The remote and unit should respond normally again. If your model has a specific reset method, the manual will note it.

Temp button in ac remote

The temperature controls set the room target. On a Gree remote these are usually the up and down arrows rather than a single “temp” button.

With the unit on and in Cool or Heat mode, press up or down to adjust the set temperature. The chosen value shows on the remote display, and the AC runs to reach it. Small adjustments work best.

Gree air conditioner timer off

The timer lets you schedule when the unit turns on or off automatically — useful for cooling the room before you get home or shutting off overnight.

Press the Timer button on the remote, then use the up and down arrows to set the time, and confirm per your remote’s prompt. Depending on the model, you’ll set a “Timer On” and/or “Timer Off” time.

If the AC isn’t running when you expect it to, check that a timer wasn’t left set, since an active off-timer can shut the unit down. Clearing the timer restores normal operation.

Inverter ac remote function

On an inverter AC, the compressor varies its speed instead of simply switching fully on and off. The remote works the same way for you — power, mode, temperature, fan — but behind the scenes the unit ramps the compressor up and down to hold the set temperature steadily, which saves energy and reduces temperature swings compared with a fixed-speed unit.

Frequently Asked Questions

How do I change the temperature on a Gree AC?
With the unit on and set to Cool or Heat, press the up or down arrow on the remote until your target temperature shows on the display. Make small adjustments rather than jumping to an extreme setting.

What is the “I Feel” function in a Gree AC?
It tells the AC to use the temperature sensor inside the remote instead of the one in the indoor unit. Place the remote near you and press I Feel, and the unit adjusts to make your location comfortable. An icon shows on the display when it’s on.

What are the symbols on a Gree AC remote?
The main ones are power, mode (snowflake for cool, sun for heat, water drop for dry, fan for fan-only), fan speed, and the temperature arrows. You’ll also see swing, timer, sleep, and the I Feel icon. Your model’s manual lists any symbols specific to your remote.

My Gree remote isn’t working — what should I check?
Replace the batteries first, then confirm you have a clear line of sight to the unit’s receiver and are within range. If it still doesn’t respond, reset the remote, and if that fails, contact Gree support or get a compatible replacement remote.